Ebike wall mounts: 6 That Can Carry the Weight

As an Amazon Associate I earn from qualifying purchases. Links in this article may be affiliate links. How we choose gear

A bracket strong enough for a television is not automatically strong enough for a bike. Shoppers often reason from tv wall mounts, even the full-motion arms that hold a screen out from the wall, but a TV hangs still against its studs, while an electric bike gets lifted, swung and rolled back in after every ride. One e-bike maker’s storage guide puts a typical e-bike at 50 to 80 pounds, and that load is why ebike wall mounts are rated, sized and fastened differently from ordinary bike hooks.

This 2027 shortlist sorts six real models by rated weight, tire width, fender fit and wall requirements. The findings rest on maker spec pages, installation manuals, dealer listings and owner threads on Electric Bike Review and EMTB Forums; none of the six was installed or loaded for this guide, so every comment about handling belongs to a named source. Prices appear as ranges from those pages, and the current price on Amazon.com may differ.

Four numbers that decide whether a mount fits your bike

Rated weight comes first, and it needs headroom. Engwe, an e-bike maker, advises choosing a mount rated for at least 1.5 times the bike’s weight with the battery installed. Run that rule across the six picks (our arithmetic) and a 77-pound rating covers a bike of about 51 pounds, a 100-pound rating covers about 67, and the 121-pound rating on the Steadyrack ProFlex Rack covers about 80. The 50-pound-per-hook rating on the StoreYourBoard Fat Tire BLAT Rack points to a bike near 33 pounds.

Makers rate their racks at the full figure, so the 1.5 rule is a conservative cushion rather than a limit. Taking the battery off sheds 8 to 10 pounds, according to a Leoguar Bikes storage guide, which moves a 65-pound bike toward 55 before it touches a hook.

Tire width and wheel size come second. Steadyrack’s comparison of its own racks splits the line into three bands, up to 2.1 inches, 2.1 to 2.8 inches and 2.8 to 4.5 inches, and the other mounts here list ceilings between 3.54 and 5 inches. A cradle sized for a road tire is a real constraint: an Electric Bike Review member who hangs a 50-pound Levo says the hooks struggle with its 2.6-inch tires.

Fenders are third. Several racks state flatly that fenders are unsupported, while others ask for about 3/4 inch between tire and stays. The fourth number appears on no box at all: how many studs sit where you want the bike. The wall section further down covers it.

Best ebike wall mounts side by side

The table lists what each maker or dealer page states; a blank answer means the page said nothing.

Model Rated weight Tire width Fenders Loading Wall
Steadyrack eBike Rack 77 lb 2.1″ to 2.8″ Yes, about 3/4″ clearance Roll-in pivot, 160° Timber and masonry fixings included
Delta Pivot Rack 100 lb Up to 4.25″ (dealer listings) Not stated Roll-on pivot, 150° Wood studs only
Steadyrack ProFlex Rack 121 lb Up to 2.1″, 2.1″ to 2.8″ or 2.8″ to 4.5″ Yes Pivoting rack “Structurally sound wall”
monTEK Swivel Bike Wall Mount 77 lb (some listings 66 lb) Up to 3.54″ No Roll-on swivel, 120° Wood stud or concrete
StoreYourBoard Fat Tire BLAT Rack 50 lb per hook, 100 lb total Up to 5″ Not stated Lift onto fixed hook 16″ studs
Delta Wall Ride Storage Hook 100 lb Up to 3.75″ Not stated Adjustable wall hook Wood or concrete

Only two rows state fender support outright, and the Steadyrack ProFlex Rack alone clears 100 pounds with room to spare. The two Delta racks are the budget route to a 100-pound rating, though both leave out details the pages never answer. Check the rated weight on each listing against your bike’s scale reading before ordering.

Six mounts for six kinds of ebike

1. Steadyrack eBike Rack — roll-in storage for fendered commuters

Commuter bikes with full fenders are the ones most wall racks quietly rule out, and this is the model built around them. Steadyrack’s page lists a 77-pound limit, 20-to-29-inch wheels, tires from 2.1 to 2.8 inches and at least 3/4 inch between tire and fender stays, plus a warning that the rear fender must be long enough to raise the bike onto its rear tire without scraping.

The 160° pivot lets bikes sit close together. The maker says racks can be installed as little as 350 mm (about 14 inches) apart and can overlap. The rack weighs 6.8 pounds, pairs chrome-plated steel with nylon fender saddles, and ships with fixings for timber and masonry. The maker’s page shows it at around $80 to $100.

Buyer reviews on that page average 4.9 out of 5 across 125 ratings, but the fender comments are mixed. One buyer with two Aventon PACE 500.3 bikes removed the front fenders to load them the first time and doubted the clearance; another reports his fenders fit without binding. An EMTB Forums member says a 50-pound e-MTB lives easily on the brand’s wall rack and that he bought a second.

Pros:

  • ✅ Built for fendered bikes and tires up to 2.8 inches
  • ✅ Loads without hoisting the bike overhead

Cons:

  • ❌ A 77-pound ceiling leaves little margin for a 65-pound bike
  • ❌ Wider tires need a different Steadyrack
Steadyrack eBike RackSee current price, sizes and reviews on Amazon.
Check Price on Amazon →

2. Delta Pivot Rack — 100 pounds, wood studs only

Delta’s manual is blunt: this rack should only be mounted to wood studs, and every pilot hole has to land in one. That is the main condition attached to the strongest rack in the standard-width group, which is rated for 100 pounds (45.3 kg) once installed correctly, rotates 150° either way and takes tires up to 4.25 inches on dealer listings.

Delta’s installation manual sets the rear wheel 2 to 3 inches from the wall and lets the wheel tray move in 35 mm steps up to 350 mm. It calls for a level, a stud finder, a 1/4-inch bit and a 1/2-inch socket, and the box holds two lag bolts, two small screws and foam spacers. Some dealer listings repeat a 75-pound figure beside the 100, so the manual’s number is the one to trust.

Road Bike Rider’s review called the rack a good, versatile solution and suggested lining several up along a wall for a family’s bikes. Under the 1.5 rule, 100 pounds covers a bike of about 67 pounds. Dealers list it at around $85 to $120, and the manual never addresses fenders, so measure the gap at the rear stay first.

Delta Pivot RackSee current price, sizes and reviews on Amazon.
Check Price on Amazon →

3. Steadyrack ProFlex Rack — most headroom for heavy, wide-tire bikes

Sitting in the premium tier of Steadyrack’s line (check the current price on Amazon.com), the ProFlex is the only rack on the maker’s comparison page rated above 77 pounds: 121 pounds, or 55 kg. It comes in narrow, wide and fat versions for tires up to 2.1 inches, 2.1 to 2.8 inches and 2.8 to 4.5 inches, lists fender compatibility with 3/4 inch between tire and stays, and includes the GearMate SteadySpine accessory.

Ebike Escape’s ProFlex review is the most useful real-use source in this group, because its testers describe loading heavy bikes hundreds of times. They say height planning is on you, since bikes hang at different heights depending on wheelbase and tire size, and that getting a heavy e-bike up onto its rear wheel takes practice and some strength. Steadyrack recommends roughly three inches between rear tire and wall for heavy e-bikes, per that review, and the testers left more on bikes with different wheelbases.

On the 1.5 rule, 121 pounds covers a bike up to about 80 pounds, the top of the 50-to-80-pound range quoted earlier.

Steadyrack ProFlex RackSee current price, sizes and reviews on Amazon.
Check Price on Amazon →

4. monTEK Swivel Bike Wall Mount — no-lift loading for fenderless bikes

Listings for this brand disagree with one another. The 77-pound version, part number VA1007RE, pairs an alloy-steel body and 120° swivel with a four-level arm for 16-to-29-inch wheels and tires up to 3.54 inches, while other monTEK multi-packs list 66 pounds and 150° of rotation. Hardware for wood studs or concrete comes with it, and the current price is on Amazon.com.

Fenders are the dividing line. The Walmart listing and several Thewearify roundups state that the mount is not compatible with bikes that have fenders. Those roundups add that the swivel can need occasional tightening, that the instructions are minimal and that the rear stabilizer feels less sturdy than a steel cradle. They repeat across several of that site’s articles and are not lab tests, so read them as one outlet’s recurring view.

The draw is the roll-on motion: per Thewearify, you set the rear wheel on a floor stabilizer, lift the front wheel into the cradle and roll the bike upright without hoisting its full weight.

Pros:

  • ✅ Arm adjusts across 16- to 29-inch wheels
  • ✅ Swivel folds the bike flat toward the wall

Cons:

  • ❌ No fender support
  • ❌ Listings disagree on the rated weight

At 77 pounds, it clears a bike of about 51 pounds under the 1.5 rule and sits close to its limit with anything heavier.

monTEK Swivel Bike Wall MountSee current price, sizes and reviews on Amazon.
Check Price on Amazon →

5. StoreYourBoard Fat Tire BLAT Rack — two-bike bar for lighter fat tires

Fifty pounds per hook, 100 pounds in total, is the number to hold up against your bike’s scale reading. The rack is a welded, powder-coated steel bar 17 inches wide, 7.5 deep and 3 tall, with two 6.5-by-5-inch slots for wheels up to 5 inches wide. It mounts with two lag screws into 16-inch stud spacing, carries a lifetime warranty and shows a 5.0 rating from 12 reviews on the maker’s page, none of which mention e-bikes. It runs around $35.

Fixed hooks mean you lift the bike. An Electric Bike Review original poster with three e-bikes reports they were too heavy to lift and hang by the front wheel even with the batteries out, while another member hangs a 50-pound Levo that way, with effort. An older thread in the same forum warns that a rear fender’s end scrapes the garage floor while you flip the front wheel up to a hook on a 55-to-60-pound bike.

The rating is per hook, so a 60-pound bike already exceeds a single slot’s 50 pounds.

StoreYourBoard Fat Tire BLAT RackSee current price, sizes and reviews on Amazon.
Check Price on Amazon →

6. Delta Wall Ride Storage Hook — cheapest 100-pound rating here

At around $40 on a dealer page, this is the least expensive 100-pound rating among the six. The listing describes a wall-mounted hook that holds one bike by a wheel, with an adjustable loading mechanism, a fold-up design, a rubberized wheel coating and tires up to 3.75 inches. It measures 72 inches long and 6.1 wide with a full-length wheel guard, includes a scuff saver for the wall and has a D-ring for a cable lock (the lock is sold separately).

That dealer page never mentions e-bikes and doesn’t say whether the 100-pound figure was set with them in mind, although a Thewearify roundup lists the hook among its picks for heavy e-bikes. The page also leaves out which screws or anchors ship in the box, so confirm the hardware before drilling into a stud.

Delta Wall Ride Storage HookSee current price, sizes and reviews on Amazon.
Check Price on Amazon →

Ebike wall mount vertical or horizontal: where the weight lands

All six picks hang the bike vertically, with one wheel in a cradle or hook and the other near the wall. That frees floor space, and a pivot arm lets neighbors sit close. The cost is handling: a Punkride storage guide rates vertical mounts as high-effort because the bike must be lifted, while horizontal racks take a wide stretch of wall, as Engwe’s storage guide notes.

Horizontal cradles tend to ask for less lifting, but their ratings are the problem. A listing for the PRO BIKE TOOL Bike Wall Mount says it is designed to hold up to 48.5 pounds, and a listing for the Vibrelli Bike Wall Mount says 55 pounds, both below the 50-to-80-pound range. The PRO Bike Wall Mount Sport says it suits all bicycle types, e-bikes included, yet its page lists no weight limit, which is exactly the number to demand before buying.

Hanging by the front wheel also raises a question about the fork. An Electric Bike Review member says he would hesitate to hang an e-bike that way given the extra weight, and another keeps his hook low enough that most of the load stays on the rear wheel. One owner of a heavy fat-tire e-assist bike on a Steadyrack Classic Rack mounted it slightly low and slides a small paving stone under the rear tire to ease the load on the headset and fork, a workaround from a single buyer review, not maker guidance. The maker’s own FAQ says no part of the frame touches the rack, only the front tire.

Before you drill: what tv wall mounts teach about studs

Anyone who has hung tv wall mounts, including the tv wall mounts full motion kind with an extending arm, knows the first job is finding studs. Angi’s drywall guide says the same for heavy mirrors and large TVs: mount into a stud or use anchors rather than the drywall alone. Bike rack makers are stricter. Delta says wood studs only, StoreYourBoard asks for 16-inch stud spacing and doesn’t include masonry anchors for concrete, and Steadyrack asks for a structurally sound wall with timber or masonry fixings.

This Old House’s guide to hanging heavy objects says anchors should hold four times the weight of the object and calls a stud finder the most reliable way to locate studs. Four times a 65-pound bike is 260 pounds, and Angi’s anchor chart tops out at 100 pounds for toggle bolts (our arithmetic), which is why the manuals point to studs. Homes with steel studs need special fasteners, according to Lowe’s wall-hanging guide.

Placement matters as much as fasteners. Leave about three inches between the rear tire and the wall, as Delta’s manual and Ebike Escape’s testers describe, and allow the 350 mm spacing Steadyrack gives for neighboring racks. Keep the battery in mind as well. A Battery Network rider guide advises storing e-bike batteries in a ventilated area with fire detection and away from entry and exit doors, and the CPSC Micromobility Information Center reports that many lithium-ion fires happen at night while batteries charge, advising use of the manufacturer’s charger only.

Ebike wall mounts reviews: what owners keep reporting

Reading ebike wall mounts reviews on retailer pages tells you less than reading the complaints, and three recur across the sources opened. Fender clearance is the first. A Steadyrack buyer pulled his front fenders, an Electric Bike Review member warned about rear-fender scraping, and the monTEK listings rule fenders out entirely, so several separate sources point at the same trouble spot.

Effort is the second. The Electric Bike Review threads, Ebike Escape’s testers and the Punkride guide agree that tipping a heavy e-bike onto a wheel takes strength or practice, which is why roll-in pivots earn their price premium. On the positive side, a Steadyrack Classic Rack reviewer called it a huge improvement over fixed-hook racks he had used before.

Third, the numbers disagree. The monTEK mount appears at 77 and 66 pounds, the Delta Pivot Rack at 75 and 100 on dealer pages, and Steadyrack’s tire bands change between its lines. When a listing and a manual differ, the manual is the safer figure.

Weight, fenders and drywall: the quick answers

❓ How much weight should an ebike wall mount hold?

✅ Weigh the bike with its battery on, then choose a rating with room to spare. One e-bike maker suggests 1.5 times the bike's weight. Most listings here run 77 to 100 pounds, so a 65-pound bike fits only the higher ratings under that rule.

❓ Can you store an ebike on a wall mount without lifting it?

✅ Pivot racks are built for roll-in loading: you tilt the bike onto its rear wheel and walk the front wheel into the cradle. Fixed hooks make you hoist the front wheel yourself, which Electric Bike Review members describe as hard with bikes near 50 pounds.

❓ Do ebike wall mounts work with fenders?

✅ Only some do. A few pivot racks list fender compatibility, usually needing about 3/4 inch between tire and fender stays, while others state no fenders at all. Compare the rack's fender and tire-width lines against your bike before you order.

❓ Can a bike rack go into drywall like tv wall mounts?

✅ Not safely by itself. Drywall holds little without a stud or heavy-duty anchor, and one maker's manual says its rack should go only into wood studs. Find the studs with a stud finder and confirm what hardware ships in the box.

❓ Where should an ebike battery be while the bike hangs on the wall?

✅ Away from entry and exit doors, in a ventilated space with fire detection, according to a Battery Network rider guide. CPSC reports that many lithium-ion fires start while batteries charge at night and advises using only the maker's charger.

Choosing among the best ebike wall mounts

Weigh your bike with the battery on, add headroom, then match the rest. A fendered commuter under about 65 pounds suits the Steadyrack eBike Rack; a heavier or wide-tire bike belongs on the Steadyrack ProFlex Rack; and anyone with solid wood studs who needs a 100-pound rating can take the Delta Pivot Rack as the lower-cost route. The monTEK Swivel Bike Wall Mount fits fenderless bikes, while the StoreYourBoard Fat Tire BLAT Rack and Delta Wall Ride Storage Hook leave the lifting to you.

Whichever of these ebike wall mounts you pick, the rating, tire width and stud location decide the outcome, not the finish or the swivel angle. Start with the scale reading.

Recommended for You

Disclaimer: This post contains affiliate links. As an Amazon Associate, we earn from qualifying purchases made through these links, at no additional cost to you.


Before you add one to your cart, compare the exact model number against your bike’s weight and tire width.

Author

  • NextGenEBike Team

    NextGenEBike is an independent buying-guide site for electric bikes, motors, batteries and accessories. Our editorial team compares products using manufacturer specifications, independent tests from specialist e-bike media, owner reports and retailer listings. We do not claim to have tested the products ourselves; see How We Choose Gear for our method.

    View all posts